驗貨感應燈時，需要從外觀、功能、安全性等多個方面進行檢查，以確保產品符合質量標準和客戶的要求。以下是詳細的感應燈驗貨步驟：

1. 外觀檢查

外殼狀況：檢查感應燈外殼是否有劃痕、裂縫、變形等明顯的損壞或瑕疵。

顏色一致性：確保燈體顏色均勻，無明顯色差。

零件完整性：檢查燈具各個部件是否齊全，如燈罩、底座、感應器等。確保各個連接部位牢固無松動。

清潔度：確保表面干凈，無油污、灰塵或其他雜物。

2. 功能測試

感應功能：

感應范圍：測試感應燈的感應距離和角度。使用身體或手移動來模擬觸發感應，確保感應器在規定范圍內能夠準確探測到運動。

感應靈敏度：檢查感應燈的靈敏度，確保在感應距離內能夠迅速響應并點亮。

延時關閉功能：測試感應燈的延時功能，觀察燈是否在設定的時間內自動關閉，并確保延時功能符合說明書的描述（例如幾秒或幾分鐘）。

光照強度：使用照度計或肉眼觀察感應燈的亮度，確保亮度符合產品規格。

模式切換測試：如果感應燈具有不同的模式（如夜間模式、節能模式等），逐個進行切換測試，確保每種模式正常運行。

3. 電氣性能測試

功率測試：使用功率計測試感應燈的功率，確保功率值與標注的額定功率一致。

電壓測試：檢查感應燈在不同電壓條件下是否能正常工作，特別是在額定電壓下的穩定性。

電源線檢查：確保電源線無破損、連接牢固，插頭正常使用。

耗電情況：對于節能型感應燈，測試其耗電量，確保在低耗電的能正常工作。

4. 安全性檢查

防水性能：如果是戶外感應燈，需要進行防水測試（IP等級），確保燈具在暴露于雨水或潮濕環境下不會進水或損壞。

絕緣和漏電測試：使用絕緣電阻測試儀檢測感應燈的絕緣性能，確保不會發生漏電風險。必要時進行接地電阻測試，確保符合安全標準。

過熱保護功能：測試感應燈長時間工作時，是否具備過熱保護功能，檢查其散熱效果，確保不會因?yàn)檫^熱而損壞或引發火災風險。

5. 光感檢測

日夜感應測試：如果感應燈具備光感功能，應在不同光照條件下（明亮和黑暗環境）測試感應燈的反應，確保白天不亮、夜晚才啟動。

環境適應性：測試在不同光照條件下，感應燈是否能正確感應光線并啟動。

6. 耐用性與可靠性測試

開關壽命測試：通過多次啟閉感應燈，模擬日常使用，確保其在反復使用的情況下，燈具和感應器都能正常工作且無故障。

跌落測試：對便攜式或移動式感應燈進行低高度（如1米）跌落測試，檢查其在受到外部沖擊后是否還能正常工作，外殼是否出現裂縫或破損。

7. 包裝與配件檢查

包裝完整性：檢查包裝是否牢固，防護措施是否到位（如泡沫、塑料袋、說明書等），以確保運輸過程中不會損壞。

配件齊全：確認所有配件是否齊全，例如螺絲、安裝支架、充電線（如為充電款式），并核對說明書中的配件清單。

標識清晰度：檢查包裝及產品本身的標簽，確保有清晰的產品名稱、型號、功率、生產日期、認證標志（如CE、FCC等）等信息。

通過上述驗貨步驟，可以確保感應燈的質量、安全性和功能性達到要求，并能有效使用。

Inspecting an induction (sensor-based) light involves checking its functionality, safety, durability, and overall Here's a step-by-step guide to properly inspect an induction light:

1. Visual Inspection

Housing Condition: Examine the      light's exterior for any visible damage, such as cracks, dents, or      scratches. The housing should be intact, without any deformation or sharp      edges.

Color Consistency: Ensure the      light’s housing has consistent color and finish across all units.

Component Completeness: Check if      all parts are present, such as the light cover, sensor, mounting brackets,      or power cables. Ensure these components are firmly attached.

Cleanliness: The exterior should be      free of dust, oil, or any visible debris.

2. Functional Testing

Sensor Functionality:

Detection Range: Test the       induction light’s sensor by moving within the stated detection range and       angle. Ensure the sensor responds accurately by turning the light on       within the designated range.

Sensor Sensitivity: Test the       light's sensitivity by varying the distance and speed of movement in       front of the sensor to check if it activates as intended.

Auto-off Timer: After activation,       measure the time it takes for the light to turn off. Ensure the delay       matches the specified settings (e.g., 30 seconds, 1 minute).

Lighting Performance:

Brightness: Use a lux meter to       measure the light output and ensure the brightness is within the       product's specifications.

Light Spread: Observe the light       distribution to ensure it spreads evenly without dark spots or shadows.

Mode Settings: If the light offers      different modes (e.g., night mode, energy-saving mode), switch between      them and verify each mode works as expected.

3. Electrical Testing

Power Consumption: Use a power      meter to verify the induction light’s power consumption matches the      manufacturer’s stated values.

Voltage Stability: Check the      light’s operation at different voltage levels (particularly the rated      voltage) to ensure it functions without flickering or shutdowns.

Cable and Plug: Inspect the power      cord for damage or weak points. Ensure the plug is securely connected and      functions correctly.

Energy Efficiency: For      energy-efficient lights, verify their power consumption aligns with      energy-saving standards.

4. Safety Testing

Waterproofing (for Outdoor Lights):      If the induction light is intended for outdoor use, perform an IP rating      test (e.g., IP65 for water resistance) by spraying water to ensure it      remains operational without water intrusion.

Electrical Insulation: Test the      light’s insulation resistance using an insulation tester to ensure there’s      no risk of electrical shock or short circuit.

Leakage Current Test: Perform a      leakage current test to ensure the light does not have excessive      electrical leakage, which could pose a safety risk.

Overheat Protection: Run the      induction light for an extended period and monitor its temperature. Ensure      that it doesn’t overheat or pose a fire hazard. Some lights come with      built-in overheat protection features—test this by intentionally allowing      the light to reach higher temperatures.

5. Environmental and Sensitivity Testing

Day/Night Sensor Testing: If the      light has a built-in light sensor, test it by simulating different light      conditions (daylight and darkness) to ensure the light only activates at      night or in low-light conditions.

Environmental Adaptability: Test      the light in various conditions, such as extreme heat, cold, or humidity,      to ensure it performs reliably in different environments, especially for      outdoor lights.

6. Durability and Reliability Testing

Switch Cycle Test: Test the light’s      durability by turning it on and off multiple times (simulating normal      use). Ensure the sensor and light respond consistently.

Drop Test: For portable or      lightweight induction lights, drop the unit from a low height (e.g., 1      meter) to see if it can withstand shocks without damage or malfunction.

Long-Running Test: Let the light      run for an extended period to test for overheating, flickering, or sudden      shutdowns.

7. Packaging and Accessories

Packaging : Inspect the      packaging for sturdiness and sufficient protective material to ensure the      product will not be damaged during shipping.

Accessory Check: Verify that all      accessories are included, such as mounting brackets, screws, a power      adapter (if applicable), and user manuals.

Labels and Certifications: Ensure      the packaging includes important product information, such as product      name, voltage, power rating, and safety certifications (e.g., CE, UL,      FCC).

8. Weight and Build Check

Weight Check: Weigh the induction      light to ensure it matches the product specifications.

Build : Test the sturdiness      of the materials. The light should not feel flimsy, and all parts should      fit together well without rattling or gaps.

By following these steps, you can ensure that the induction light meets standards and performs its intended functions safely and efficiently.

1. Visual Inspection

Housing Condition

Color Consistency

Component Completeness

Cleanliness

2. Functional Testing

Sensor Functionality:

Detection Range

Sensor Sensitivity

Auto-off Timer

Lighting Performance:

Brightness

Light Spread

Mode Settings

3. Electrical Testing

Power Consumption

Voltage Stability

Cable and Plug

Energy Efficiency

4. Safety Testing

Waterproofing (for Outdoor Lights)

Electrical Insulation: Test the light’s      insulation resistance using an insulation tester to ensure there’s no risk      of electrical shock or short circuit.

Leakage Current Test

Overheat Protection

5. Environmental and Sensitivity Testing

Day/Night Sensor Testing

Environmental Adaptability

6. Durability and Reliability Testing

Switch Cycle Test

Drop Test

Long-Running Test

7. Packaging and Accessories

Packaging

Accessory Check

Labels and Certifications

8. Weight and Build Check

Weight Check

Build